Some plastic self sealing bags get a blind hole after forming, and then drill through. This method is suitable for thin and deep holes, which can prevent the core from deforming during forming. Plastic products have no holes after forming, and then the holes will be processed again. The latter two knife methods are limited to a few easy cutting materials, such as nylon. At the same time, it needs secondary processing. The production efficiency is low, and it is difficult to guarantee the quality of fine holes, so it is rarely used. This section mainly introduces the design principle and processing method of holes directly generated during forming.

对在成型时直接生成的孔，无论伺种类型，均应设置在不易削弱制品强度的部位，且孔的形状应力求不使模具制造工艺复杂化。是在成型的制品残留熔接痕和削弱强度的重要因素。周围设一个凸边来加强。同时，孔与孔的间距及几到制品边缘的距离也要适当。所示的尺寸关系确定，当两个孔不一“样大小时，按小7L取值；热塑性塑料自封袋的注塑制品按表2—7中数值的75％取恒。对于孔的深度，不同类型的孔的深度因成型方法的不同而不同。通孔注塑制品L的通扎用得很多，成型通孔用的型芯一般有以门L种安装办法。

For the holes directly generated during forming, regardless of the type, they should be set at the parts that are not easy to weaken the strength of the products, and the shape of the holes should strive not to complicate the mold manufacturing process. It is an important factor for residual weld lines and weakening strength of formed products. Set a convex edge around to strengthen. At the same time, the distance between holes and the edge of the product should also be appropriate. The dimension relationship shown is determined. When two holes are different in size, the value is taken as 7L smaller; the injection molded products of thermoplastic self sealing bags are taken as 75% of the values in table 2-7. For the depth of holes, the depth of different types of holes varies with different molding methods. Through hole injection molded products L are used a lot, and the cores used for forming through holes generally have l installation methods.

内一端固定的型芯来成型，且易生成飞边，当型芯较细时易弯曲。这种固定型芯的方法不能成型深孔。由两个两端固定的则芯来成型，由于将一个型芯设计得比另一个大o．5—1mm左右，保证孔的同心度，不于引起安装和使用土的困难，而且增加了型芯的稳定性，孔的精度低。由一端固定，一端导向支撑的型芯来成型，这样型芯有较好的强度和刚度，又能保证同心度，但导向部分易因导向误差磨损而产生圆弧溢料。以上无论采用何种固定方法，孔的深度均不能太大，公则型芯会弯曲。通常九探随塑料流动性的4(同而不同，流动性好的塑料自封袋的7L的深度可以达到10倍孔径，流动性中等的不能超过7倍孔径，而流动性差的塑料制品的孔深小于4倍7L径；否则只能采取机械加工的力法获得。

It is easy to produce flash and bend when the core is thin. This method of fixing the core cannot form deep holes. It is formed by two cores fixed at both ends. Because one core is designed to be about 0.5-1mm larger than the other, the concentricity of the hole is guaranteed, which will not cause difficulties in installation and use of soil, but also increase the stability of the core, and the accuracy of the hole is low. It is formed by the core with one end fixed and one end guided and supported, so that the core has better strength and stiffness and can ensure concentricity, but the guide part is easy to produce arc overflow due to the wear of guide error. No matter what fixing method is adopted above, the depth of the hole should not be too large, and the core will be bent. Generally, the depth of 7L of plastic self sealing bag with good fluidity can reach 10 times the aperture, and that of plastic products with medium fluidity can not exceed 7 times the aperture, while that of plastic products with poor fluidity is less than 4 times the 7L diameter; otherwise, it can only be obtained by mechanical processing.

以上就是为大家介绍的有关济南自封袋的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务.//www.haaimobile.com

The above is a detailed introduction about Jinan self sealing bag. I hope it will help you If you have any questions, please contact us We will provide you with professional service //www.haaimobile.com